New Service
Custom 3D Print Fabrication
FDM 3D printing in Covington, Georgia. Prototypes, props, custom parts, and appliques. Two machines, six materials, multi-colour prints, and builds up to 350mm.
Two printers, and the part decides which
We run whichever machine fits your part. Smaller work goes to the precision printer; anything larger, or anything needing an engineering material, goes to the K2 Plus. You are quoted at that machine's rate.
FlashForge Adventurer 5M Pro
The precision machine. Fast, clean surfaces, tight tolerances on small parts.
- Build volume
- 220mm cubed
- Rate
- $10.00 setup + $6.00/hr
- Colours per print
- One material
- Heated chamber
- No
Best for: Prototypes, small props, appliques, replacement parts, short runs.
Creality K2 Plus Combo
The large-format machine. Enclosed and heated, so it prints engineering materials the Adventurer cannot.
- Build volume
- 350mm cubed
- Rate
- $20.00 setup + $8.00/hr
- Colours per print
- Up to 4
- Heated chamber
- Yes, to 60°C
Best for: Helmets and full-size props, large enclosures, functional parts in ABS, ASA or carbon-fibre nylon, and multi-colour prints.
Multi-colour prints run on the K2 Plus through a four-spool filament system — $15.00 per colour past the first, because every colour change purges filament before the print carries on. Flexible TPU is single-colour only: the system cannot feed a filament that soft.
Materials
Three reliable materials, each with a clear use case. We'll recommend the right one based on what your part does.
PLA+
IncludedStandard for most jobs. Strong, easy to print, great surface finish. Included in base pricing.
PETG
+$12.00 per jobBetter heat resistance and chemical tolerance. Slightly flexible. Good for outdoor parts.
PETG-CF
+$15.00 per jobCarbon-fiber reinforced PETG. Stiff and dimensionally stable for functional parts.
ABS/ASA
+$18.00 per jobTough and heat-resistant; ASA also holds up to sun and weather. Needs the K2's heated chamber, so it is large-format only.
PA-CF
+$35.00 per jobCarbon-fiber nylon — the strongest and stiffest option, for load-bearing and wear parts. K2 only.
TPU
+$20.00 per jobFlexible, rubber-like. Gaskets, grips, soft-touch parts. Single colour only — it cannot run through the multi-colour system.
Pricing Tiers
Pricing is based on actual slicer-estimated print time, plus a setup fee. The ranges below are the FlashForge Adventurer 5M Pro at $10.00 + $6.00/hr; large-format work on the K2 Plus is $20.00 + $8.00/hr and usually lands in Extended. These tiers are honest communication buckets for the typical range.
| Tier | Description | Time | Typical Range |
|---|---|---|---|
| Quick Print | Simple geometry, minimal supports | Under 3 hrs | $25.00 – $35.00 |
| Standard Print | Moderate detail, some supports | 3–6 hrs | $45.00 – $65.00 |
| Complex Print | Dense infill, full supports, tight tolerance | 6–12 hrs | $70.00 – $120.00 |
| Extended Run | Multi-part sets, large-format builds, 12+ hours, multi-day | 12+ hrs | Quote only |
Rush turnaround (same / next day): +$15 flat. Shipping: actual cost + $5 handling.
For makers + cosplayers
Cosplay & Props
Your local Covington print bureau. Bring an STL or 3MF — what you already get from Etsy, Cults3D, or Thingiverse — and we print it clean and accurate so you can finish it your way. Supports removed, parts ready for your build.
| Item | Starting at |
|---|---|
| Small prop / mask piece / accessory | from $25 |
| Bracer / gauntlet pair | from $55 |
| Helmet — full, multi-part | from $70 |
| Sword or staff | from $80 |
| Chest piece / large armor | from $110 |
| Full set or custom build | flat quote from your file |
“From” prices are starting points in PLA+. We confirm the exact number the same day, straight from your file. Bigger sets, denser geometry, or PETG / PETG-CF material upcharge a little higher — covered in the tiers above.
Get an Instant Estimate
Six quick questions. Estimate only — exact price is confirmed after we slice your file.
1. Do you have an STL or 3MF file ready, or do you need a model designed from scratch?
How It Works
Four standing rules, applied to every job — they make the service predictable for you and sustainable for us.
Payment first, print after
Every job invoices via Stripe Payment Link. Print queue does not start until payment is confirmed. No exceptions — this protects both sides.
350mm hard ceiling
Two machines: parts up to 220mm run on the Adventurer 5M Pro, and up to 350mm on the K2 Plus. Past 350mm we can split the design ($50–$75) or coordinate outsourcing ($15 fee).
Delivery, not pickup
Local Covington-area drop-off by us, or shipped via USPS/UPS with tracking (actual cost + $5 handling). No customer pickup at our premises.
Estimates aren't guarantees
The instant estimate below is a ballpark. We confirm the exact quote after slicing your STL file and seeing the real print time.
Ready to send your file?
Email your STL or 3MF along with quantity, material preference, and deadline. We'll confirm the exact quote and send a Stripe Payment Link.